Anca AMD2000 Series Manuale Utente Pagina 149
- Pagina / 189
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Fault Tracing
ANCA Motion DS619-0-00-0019 - Rev 0 149
11
2. Encoder cable is disconnected.
3. Encoder cable is wired incorrectly.
4. Encoder is not analogue.
5. Encoder is not outputting the correct voltage.
6. Encoder is faulty.
7. Drive is faulty. Please contact ANCA Motion for support.
Severity
Error
Encoder Amplitude High - External E0028
Description
The magnitude of the signals coming from the external analogue encoder is too high. Possible
causes for this error are:
1. Encoder cable is wired incorrectly.
2. Encoder is not analogue.
3. Encoder is not outputting the correct voltage.
4. Encoder is faulty.
5. Drive is faulty. Please contact ANCA Motion for support.
Severity
Error
Excess Difference in Position Feedback E0033
Description
The difference between motor and external feedback is greater than the configured threshold.
Possible causes for this error are:
1. Incorrect encoder line count.
2. Incorrect gear box ratio and/or feed constant.
3. Faulty drive mechanism (eg. loss coupling).
4. Faulty encoder.
5. Fault drive. Please contact ANCA Motion for support.
Severity
Error
Variable Torque Limit Error E0080
Description
Configuration of the variable torque limit is invalid. The minimum torque limit is configured
larger than the maximum torque limit.
Severity
Error
Drive Not Configured E0100
Description
The drive has been enabled before being configured
Severity
Error
Amplifier Temperature Sensor Error - High E0101
Description
Drive power stage temperature sensor is reading a value higher than the drive's sensor
operating range. Drive is faulty. Please contact ANCA Motion for support.
Severity
Error
Amplifier Temperature Sensor Error - Low E0102
Description
Drive power stage temperature sensor is reading a value lower than the drive's sensor
operating range. Drive is faulty. Please contact ANCA Motion for support.
Severity
Error
Amplifier Temperature High Warning W0103
Description
The drive amplifier (power stage) temperature exceeds the hardware's warning level. Possible
causes for this error are:
1. Operating environment is outside specification.
2. Drive ventilation is insufficient.
- AMD2000 Series - Servo Drive 1
- Contents 4
- 1. Safety 10
- Safety 11
- 2. Introduction 12
- 2.1.15 Related Documents 13
- 2.1.17 Trademarks 13
- 3. Product Overview 14
- 3.3 Operating Principle 15
- D2009-2S1-A 16
- 3.5 System Overview 17
- Product Overview 19
- 3.6 Connector Overview 20
- 3.6.12 AMD2000 9A 21
- 3.6.12.4 22
- 3.6.12.7 23
- 4. Mechanical Installation 25
- Mechanical Installation 27
- 4.4 Installation 28
- STEP2 STEP 3 STEP 4 29
- Thermal Overload 5.5.11.1 31
- 5.6 Power Cable Selection 32
- 5.7 Control Cable Selection 33
- 5.8 Cable Routing 33
- 6. Power Wiring 35
- Power Wiring 37
- Heatsink 38
- PE connection 38
- 6.6 Power Supply Filters 41
- 6.8 Motor Connections 44
- 6.8.12.1 45
- Protective Earth Wire to 47
- Metal P-Clip 49
- Exposed Metal Braid 49
- Armature Cable from 3A 49
- 6.9 Drive Output Filters 50
- 6.10 Motor Brake Connection 52
- 6.11 Motor Thermal Switch 52
- 6.12 Motor Thermal Sensor 53
- 7. Control Wiring 55
- 7.2.12 Analogue Outputs 57
- 7.3 Digital I/O 58
- 7.3.12.1 59
- 7.3.12.1.2 60
- 7.3.12.2.2 60
- Digital Outputs 7.3.12.3 61
- 7.6.11 EtherCAT® 62
- EtherCAT 63
- Slave Controller 63
- 7.8 Motor Feedback 65
- 7.7 DIP Buttons 65
- Control Wiring 67
- 8. Installation Checklist 68
- Installation Checklist 69
- 9. Start-up 70
- 9.6 Starting the AMD2000 71
- Start-up 73
- 9.8.11 ANCA MotionBench 77
- 10. Feature Configuration 87
- Figure 10-1 Circle Graph Tab 89
- Figure 10-2 Time Domain Tab 89
- 10.1.15 Drive Bypass Mode 97
- ANCA Motion 100
- Feature Configuration 101
- 10.1.17 Encoders 103
- S-0-0151 / 151 115
- S-0-0403 / 403 115
- P-0-0257 / 33025 119
- 10.1.20 Modulo Operation 121
- 10.1.22 Motor Control 129
- P-0-033 / 32801 131
- P-0-034 / 32802 131
- – EOL calibrated 131
- If Motor Type =PMSM 133
- Field Weakening 133
- 10.1.23 Operating Modes 139
- 11. Fault Tracing 144
- 11.3 Supported Error Codes 145
- Fault Tracing 147
- Error E0007 148
- Too Many Errors I0666 156
- Task Overrun W1002 156
- 12. Technical Data 158
- Technical Data 159
- 12.3.16 Analogue Inputs 161
- 12.3.17 Analogue Outputs 161
- 12.3.19 Encoder Channel 1 161
- 12.4.12 Digital servo drive 163
- 12.6.11 Storage 165
- 12.6.12 Transport 165
- 12.6.15 Cooling 165
- 12.7 Dimension Drawings 166
- 12.10 Temperature De-rating 169
- 12.12 Discharge Period 171
- 12.13 Motor Output Power 171
- 12.15 Materials 174
- 12.16 Standards Conformity 175
- 12.17 EtherCAT® 176
- Conformance Marking 176
- 12.18 CE Marking 176
- Definitions 12.18.12.1 177
- M A 6 0 - 0 6 3 0 - A B 180
- K 2 A - F S P D - 0 2 0 183
- 13.4 Other Accessories 184
- 13.4.12 EtherCAT Cables 185
- 13.4.14 AMD2000 3A EMC Kit 185
- 13.4.15 AMD2000 9A EMC Kit 185
- 13.5 Starter Kits 186
- Accessories 187
- 14. Additional Information 188
- 14.4 Feedback 189
© 2020, manymanuals.it. Tutti i diritti riservati | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale